Northern Ireland Electric Gates Lisburn

Published Sep 21, 22
4 min read

Electric Gate Motor lisburn

The following information will describe all you require to know to determine which 'Linear Ram' electric gate motors are best for you - Electric Gate Service Near Me Lisburn. Prior to choosing a proper motor you will need some fundamental info about your gate set up and environment. The info can then be used to cross reference with the motor specifications and producer standards. Electric Gates.

The number of gate operations per hour will identify which type of power output is needed. Selecting a motor suitable with your expected use is important for its sturdiness and safe operation.

If the electrical gate is meant to be in usage more frequntly (+15 times per hour) then a 24v system is recommended. 24v systems run cooler than 230v electric gate motors which permits more intensive use. 24v electric gate motors tend to be used on commercial/communal facilities, where as 230v on basic domestic homes.

Electric Gate Systems lisburn

Each manufacturer will have a variety of electrical gate motors which run up to a maximum weight. The weight limit guarantees the motor will operate the gate/s in a trustworthy and safe way by offering the right amount of torque. Under-powered motors will not hit their opening/closing points and over-powered motors may cause damage to eviction and/or hinges. Electric Gates.

The motor mechansim will differ in size to fit the width of the gate (Electric Gates). Its essential to note the motor 'max' width can be higher than your gate (to a particular extent as per producer guidelines) but not lower. If the 'max' width of the motor is lower than the measurement of your gate, it will not gain the required utilize to reach its fully open or closed positions.

Electric Gates Repairs Near Me lisburnSliding Electric Gates lisburn

 Here are some of the services we provide:

  • Electric Gates Lisburn
  • Electric Gate Lisburn
  • Electric Sliding Gates Lisburn
  • Electric Gates Near Me Lisburn
  • Electric Driveway Gate Lisburn
  • Electric Gate Opener Lisburn
  • Electric Gates Cost Lisburn
  • Electric Driveway Gates Lisburn
  • Electric Gates for Driveways Lisburn
  • Electric Gate Repair Near Me Lisburn
  • Electric Gate Openers Lisburn
  • Wooden Electric Gates Lisburn

Give Adrian a Call on 07855-781433 for help or advice

AutoGate Northern Ireland
110 Stockmans Ln, 

The most common type of on-gate electric motors are direct rams, they cover practically all gate formats. Direct Rams run the gates through a curved trajectory.

Electric Gate Maintenance lisburn

The 'stroke length' is the operating length of the motor arm. The A/B measurements are calculated as follows: Total stroke length (minus 15-20mm depending upon the producer - the motors can not utilize their total operating length so an arrangement is given) divided by 2. This then offers you the A/B measurements which form the pivot point to mount the motor for optimal mechanical leverage.

Complete growth 980mm minus complete retraction 665mm = 315mm stroke length (Electric Gate Entry Systems Lisburn). Provision for the motor is 15mm, leaving 300mm. Electric Gates. 300mm divided by 2 = 150mm A = 150mm B = 150mm To get the maximum geometry the motor's pivot point ought to be placed 150mm x 150mm from the centre of eviction hinge.

Setting up the motor outside of these tolerences will put the motor at danger and also void the warranty. Usually speaking if A is minimized, B will be increased by the same quantity and vice versa to remain within the motors permitted geometry - Electric Gates.

Electric Garden Gates lisburn

The D dimension just enters play for side hung gates. The D measurements are detailed together with the A & B dimensions within the set up parmater tables. Electric Gates. The D measurement is the range from the centre of the hinge to the ouside edge of the pillar (as detailed in the diagram above).

If the hinge position procedures higher than defined, installing the motor is not possible. For the simple reason - the motor itself will come into contact with the corner of the pillar and avoid the gate from opening or closing.

Electric Gate Controller lisburnElectric Gate Maintenance Near Me lisburn

The bracket needs to be installed so the pivot point of the motor (the pin) accompanies the A & B measurements (And D if side hung). Typically the bracket is either bolted or welded to the pillar or post. You will require the following measurements to identify whether the motor bracket can be directly mounted to the post. Electric Gates.

Residential Electric Gates Ni lisburn

If your pillar width is too small to install the motor bracket straight (which is really common when retro fitting gate motors) then an extra post may be required or an adjusted bracket. Many electrical gate motors need a physical stop at the end of the opening and closing cycle.



Latest Posts

Northern Ireland Electric Gates Lisburn

Published Sep 21, 22
4 min read

Residential Electric Gates Cost Lisburn

Published Sep 18, 22
4 min read

Electric Driveway Gates Lisburn

Published Sep 18, 22
4 min read