Northern Ireland Electric Gates Lisburn

Published Sep 18, 22
4 min read

Electric Gates For Driveways lisburn

The following information will explain all you require to know to determine which 'Direct Ram' electrical gate motors are best for you - Electric Gates Near Me Lisburn. Prior to choosing an appropriate motor you will need some standard info about your gate established and environment. The details can then be utilized to cross referral with the motor requirements and maker standards. Electric Gates.

Both types can be wired directly from your mains power. The number of gate operations per hour will figure out which type of power output is required. Motors are developed to operate within a certain capability (operations per hour). Selecting a motor suitable with your anticipated use is important for its resilience and safe operation.

If the electric gate is meant to be in use more frequntly (+15 times per hour) then a 24v system is suggested. 24v systems run cooler than 230v electrical gate motors which permits more intensive usage. 24v electric gate motors tend to be used on commercial/communal facilities, where as 230v on standard domestic properties.

Electric Gates Northern Ireland lisburn

Each producer will have a range of electrical gate motors which operate as much as an optimum weight. The weight limit guarantees the motor will operate the gate/s in a trusted and safe way by supplying the right quantity of torque. Under-powered motors will not strike their opening/closing points and over-powered motors might cause damage to the gate and/or hinges. Electric Gates.

The motor mechansim will vary in size to fit the width of eviction (Electric Gates). Its essential to keep in mind the motor 'max' width can be higher than your gate (to a specific extent as per producer standards) however not lower. If the 'max' width of the motor is lower than the measurement of your gate, it will not gain the required leverage to reach its totally open or closed positions.

Electric Gates Installation Near Me lisburnElectric Gate Company Near Me lisburn

 Here are some of the services we provide:

  • Electric Gates Lisburn
  • Electric Gate Lisburn
  • Electric Sliding Gates Lisburn
  • Electric Gates Near Me Lisburn
  • Electric Driveway Gate Lisburn
  • Electric Gate Opener Lisburn
  • Electric Gates Cost Lisburn
  • Electric Driveway Gates Lisburn
  • Electric Gates for Driveways Lisburn
  • Electric Gate Repair Near Me Lisburn
  • Electric Gate Openers Lisburn
  • Wooden Electric Gates Lisburn

Give Adrian a Call on 07855-781433 for help or advice

AutoGate Northern Ireland
110 Stockmans Ln, 

The most common form of on-gate electric motors are direct rams, they cover almost all gate formats. Direct Rams run the gates through a curved trajectory.

Electric Gates lisburn

The 'stroke length' is the operating length of the motor arm. The A/B measurements are computed as follows: General stroke length (minus 15-20mm depending on the manufacturer - the motors can not use their total operating length so an arrangement is offered) divided by 2. This then gives you the A/B measurements which form the pivot point to install the motor for optimum mechanical utilize.

Complete expansion 980mm minus total retraction 665mm = 315mm stroke length (Electric Gates NI Lisburn). Arrangement for the motor is 15mm, leaving 300mm. Electric Gates. 300mm divided by 2 = 150mm A = 150mm B = 150mm To get the optimum geometry the motor's pivot point ought to be placed 150mm x 150mm from the centre of eviction hinge.

Setting up the motor outside of these tolerences will put the motor at threat and also void the service warranty. Usually speaking if A is minimized, B will be increased by the exact same amount and vice versa to remain within the motors allowed geometry - Electric Gates.

Electric Gates Belfast lisburn

The D measurement only comes into play for side hung gates. The D measurements are in-depth together with the A & B dimensions within the install parmater tables. Electric Gates. The D measurement is the range from the centre of the hinge to the ouside edge of the pillar (as detailed in the diagram above).

If the hinge position steps higher than defined, setting up the motor is not possible. For the basic factor - the motor itself will come into contact with the corner of the pillar and prevent eviction from opening or closing - Electric Gates. This usually accompanies over-sized pillars. If this holds true then an articulated arm would be a better choice.

Electric Gate Install Near Me lisburnElectric Gate Installer Near Me lisburn

The bracket must be installed so the pivot point of the motor (the pin) corresponds with the A & B measurements (And D if side hung). Usually the bracket is either bolted or bonded to the pillar or post. You will need the following measurements to determine whether the motor bracket can be directly installed to the post. Electric Gates.

Electric Gate Repairs Near Me lisburn

If your pillar width is too little to mount the motor bracket directly (which is extremely typical when retro fitting gate motors) then an extra post may be needed or an adapted bracket. Many electrical gate motors need a physical stop at the end of the opening and closing cycle.



Latest Posts

Northern Ireland Electric Gates Lisburn

Published Sep 21, 22
4 min read

Residential Electric Gates Cost Lisburn

Published Sep 18, 22
4 min read

Electric Driveway Gates Lisburn

Published Sep 18, 22
4 min read