Electric Gate Installation Lisburn

Published Sep 06, 22
4 min read

Electric Gate Installers Near Me lisburn

The following info will discuss all you require to know to identify which 'Linear Ram' electric gate motors are best for you - Electric Gate Repair Lisburn. Before choosing an appropriate motor you will need some basic details about your gate set up and environment. The info can then be used to cross reference with the motor specifications and manufacturer guidelines. Electric Gates.

Both types can be wired straight from your mains power. The variety of gate operations per hour will figure out which type of power output is needed. Motors are developed to run within a certain capability (operations per hour). Picking a motor compatible with your anticipated usage is essential for its durability and safe operation.

If the electric gate is planned to be in usage more frequntly (+15 times per hour) then a 24v system is suggested. 24v systems run cooler than 230v electrical gate motors which enables more extensive usage. 24v electric gate motors tend to be utilized on commercial/communal facilities, where as 230v on standard property properties.

Electric Gate Maintenance lisburn



Each maker will have a variety of electrical gate motors which run approximately an optimum weight. The weight limit ensures the motor will operate the gate/s in a dependable and safe manner by offering the correct amount of torque. Under-powered motors will not strike their opening/closing points and over-powered motors may trigger damage to the gate and/or hinges. Electric Gates.

The motor mechansim will differ in size to suit the width of the gate (Electric Gates). Its crucial to keep in mind the motor 'max' width can be higher than your gate (to a particular degree according to maker guidelines) but not lower. If the 'max' width of the motor is lower than the measurement of your gate, it will not gain the required utilize to reach its fully open or closed positions.

Modern Electric Gates lisburnElectric Gates Kit lisburn


 Here are some of the services we provide:

  • Electric Gates Lisburn
  • Electric Gate Lisburn
  • Electric Sliding Gates Lisburn
  • Electric Gates Near Me Lisburn
  • Electric Driveway Gate Lisburn
  • Electric Gate Opener Lisburn
  • Electric Gates Cost Lisburn
  • Electric Driveway Gates Lisburn
  • Electric Gates for Driveways Lisburn
  • Electric Gate Repair Near Me Lisburn
  • Electric Gate Openers Lisburn
  • Wooden Electric Gates Lisburn

Give Adrian a Call on 07855-781433 for help or advice

AutoGate Northern Ireland
110 Stockmans Ln, 
Belfast 
BT9 7JE


The most common type of on-gate electric motors are linear rams, they cover nearly all gate formats. Linear Rams run evictions through a curved trajectory. This forms the geometry of the the linear ram through its opening and closing cycle. Electric Gates. For linear rams the geometry is specified by 2 measurements: the 'A & B' measurements.

Electric Gate Company lisburn

The 'stroke length' is the operating length of the motor arm. The A/B measurements are determined as follows: Overall stroke length (minus 15-20mm depending upon the manufacturer - the motors can not use their overall operating length so a provision is given) divided by 2. This then offers you the A/B measurements which form the pivot point to install the motor for optimum mechanical leverage.

Full expansion 980mm minus complete retraction 665mm = 315mm stroke length (Electric Gates Kits Lisburn). Arrangement for the motor is 15mm, leaving 300mm. Electric Gates. 300mm divided by 2 = 150mm A = 150mm B = 150mm To gain the optimum geometry the motor's pivot point ought to be placed 150mm x 150mm from the centre of eviction hinge.

Installing the motor outside of these tolerences will put the motor at risk and also void the service warranty. Usually speaking if A is lowered, B will be increased by the very same quantity and vice versa to remain within the motors permitted geometry - Electric Gates.

Electric Gate Service Near Me lisburn

The D measurement only enters play for side hung gates. The D measurements are detailed along with the A & B dimensions within the install parmater tables. Electric Gates. The D measurement is the range from the centre of the hinge to the ouside edge of the pillar (as detailed in the diagram above).

If the hinge position steps greater than specified, setting up the motor is not possible. For the basic reason - the motor itself will enter contact with the corner of the pillar and prevent the gate from opening or closing - Electric Gates. This usually accompanies over-sized pillars. If this is the case then an articulated arm would be a more appropriate choice.

Electric Gate Prices lisburnElectric Gates Repair Near Me lisburn


The bracket should be mounted so the pivot point of the motor (the pin) corresponds with the A & B measurements (And D if side hung). Generally the bracket is either bolted or bonded to the pillar or post. You will need the following measurements to determine whether the motor bracket can be directly mounted to the post. Electric Gates.

Electric Gates lisburn

If your pillar width is too little to install the motor bracket directly (which is extremely common when retro fitting gate motors) then an additional post might be required or an adjusted bracket. Most electric gate motors require a physical stop at the end of the opening and closing cycle.

Navigation

Home

Latest Posts

Northern Ireland Electric Gates Lisburn

Published Sep 21, 22
4 min read

Residential Electric Gates Cost Lisburn

Published Sep 18, 22
4 min read

Electric Driveway Gates Lisburn

Published Sep 18, 22
4 min read