Electric Gate Install Near Me Lisburn

Published Sep 18, 22
4 min read

Magtec Electric Gates lisburn

The following details will explain all you require to understand to determine which 'Direct Ram' electrical gate motors are best for you - Small Electric Driveway Gates Lisburn. Prior to selecting a proper motor you will need some basic information about your gate established and environment. The information can then be used to cross reference with the motor specifications and manufacturer standards. Electric Gates.

The number of gate operations per hour will figure out which type of power output is required. Choosing a motor compatible with your expected use is necessary for its sturdiness and safe operation.

If the electrical gate is meant to be in usage more frequntly (+15 times per hour) then a 24v system is suggested. 24v systems run cooler than 230v electrical gate motors which permits more intensive use. 24v electrical gate motors tend to be utilized on commercial/communal properties, where as 230v on standard property properties.

Electric Security Gates lisburn

Each maker will have a variety of electrical gate motors which operate up to an optimum weight. The weight limitation guarantees the motor will operate the gate/s in a trusted and safe way by offering the right amount of torque. Under-powered motors will not strike their opening/closing points and over-powered motors might trigger damage to eviction and/or hinges. Electric Gates.

The motor mechansim will vary in size to suit the width of eviction (Electric Gates). Its crucial to note the motor 'max' width can be higher than your gate (to a certain level as per producer standards) however not lower. If the 'max' width of the motor is lower than the measurement of your gate, it will not acquire the required leverage to reach its completely open or closed positions.

Electric Drive Gates lisburnElectric Gate Installers lisburn

 Here are some of the services we provide:

  • Electric Gates Lisburn
  • Electric Gate Lisburn
  • Electric Sliding Gates Lisburn
  • Electric Gates Near Me Lisburn
  • Electric Driveway Gate Lisburn
  • Electric Gate Opener Lisburn
  • Electric Gates Cost Lisburn
  • Electric Driveway Gates Lisburn
  • Electric Gates for Driveways Lisburn
  • Electric Gate Repair Near Me Lisburn
  • Electric Gate Openers Lisburn
  • Wooden Electric Gates Lisburn

Give Adrian a Call on 07855-781433 for help or advice

AutoGate Northern Ireland
110 Stockmans Ln, 

The most common form of on-gate electrical motors are direct rams, they cover almost all gate formats. Linear Rams operate the gates through a curved trajectory.

Electric Drive Gates lisburn

The 'stroke length' is the operating length of the motor arm. The A/B measurements are determined as follows: Overall stroke length (minus 15-20mm depending on the manufacturer - the motors can not utilize their total operating length so a provision is given) divided by 2. This then provides you the A/B measurements which form the pivot point to mount the motor for optimal mechanical utilize.

Complete expansion 980mm minus complete retraction 665mm = 315mm stroke length (Electric Entrance Gates Lisburn). Provision for the motor is 15mm, leaving 300mm. Electric Gates. 300mm divided by 2 = 150mm A = 150mm B = 150mm To acquire the optimal geometry the motor's pivot point need to be placed 150mm x 150mm from the centre of the gate hinge.

Installing the motor outside of these tolerences will put the motor at threat and likewise void the guarantee. Usually speaking if A is minimized, B will be increased by the very same quantity and vice versa to stay within the motors allowed geometry - Electric Gates.

Driveway Gates Electric lisburn

The D measurement just comes into play for side hung gates. The D measurements are in-depth together with the A & B dimensions within the set up parmater tables. Electric Gates. The D measurement is the range from the centre of the hinge to the ouside edge of the pillar (as detailed in the diagram above).

If the hinge position steps higher than defined, installing the motor is not possible. For the simple reason - the motor itself will enter into contact with the corner of the pillar and avoid eviction from opening or closing - Electric Gates. This usually occurs with over-sized pillars. If this is the case then an articulated arm would be a more suitable alternative.

Electric Sliding Gates lisburnElectric Gates lisburn

The bracket must be mounted so the pivot point of the motor (the pin) coincides with the A & B measurements (And D if side hung). Normally the bracket is either bolted or welded to the pillar or post. You will require the following measurements to identify whether the motor bracket can be straight mounted to the post. Electric Gates.

Electric Gate Service Near Me lisburn

If your pillar width is too little to install the motor bracket straight (which is really common when retro fitting gate motors) then an additional post might be needed or an adjusted bracket. A lot of electric gate motors need a physical stop at the end of the opening and closing cycle.



Latest Posts

Northern Ireland Electric Gates Lisburn

Published Sep 21, 22
4 min read

Residential Electric Gates Cost Lisburn

Published Sep 18, 22
4 min read

Electric Driveway Gates Lisburn

Published Sep 18, 22
4 min read